C280-6 Offshore Generator Set

Standard Equipment

• Product Consist

  The engine is a turbocharged, aftercooled, four-strokecycle- diesel, electronic unit injection engine with a 280 mm (11 in) bore by 300 mm (11.8 in) stroke. SAE standard rotation is counterclockwise as viewed from the rear of engine flywheel.

• Emissions Certifications

  GL and CCS approved IMO certificate — includes statement of compliance or Engine International Air Pollution Prevention (EIAPP) certificate, supplied by the Recognized Organization (RO) where available, and technical file to be kept on board per IMO regulations.

• Marine Certification Society Type-approval

  ABS, BV, CCS, DnV, GL, LRS Spray shielding to meet SOLAS regulations for flammable fluids

• European Certifications

  Declaration of Incorporation for EU Machinery Safety Directive and EU Low Voltage Safety Directive

• Air Inlet System

  Fresh water aftercooler, corrosion resistant coated (air side) Air inlet shutoff Turbocharger, rear-mounted, oil lubricated

• Control System

  Single Cat ADEM A3 electronic engine control module with electronic unit injector fuel system, rigid wiring harness (10 amp 24V power required to drive electronic engine control modules)

• Cooling System

  Gear-driven jacket water (JW) pump Gear-driven separate-circuit aftercooler/oil cooler (AC/OC) pump Engine coolant water drains

• Exhaust System

  Dry, gas tight exhaust manifold

• Fuel System

  Distillate fuel (requires viscosity ranging from 1.4 cSt to 20 cSt at 38°C) Fuel pump, gear-driven Fuel transfer pump (mounted on left-hand side) Duplex fuel filters, rear-engine-mounted Electronically controlled unit injectors

• Lube System

  Centrifugal oil filters with single shutoff, service-side engine mounted on cylinder block inspection covers (includes installed oil lines and single shutoff valve), filters centrifuge bypass oil from the main lubricating oil pump (can be serviced with the engine running) Oil filler and dipstick Oil pressure regulating valve Dry engine-mounted sump system that gravity feeds into base assembly integral sump Engine-mounted duplex oil filter Intermittent air prelube Continuous electric prelube Redundant prelube with continuous electric prelube and intermittent air prelube backup Oil pan drain valves Electric continuous prelube pump Lube oil heater Oil pump - gear drive

• Protection System

  Crankcase explosion relief valves Alarm and shutdown during abnormal operation

• Instrumentation

  PLC-based system provides protection, monitoring, and control housed in a NEMA 4 (IP66) enclosure.

• General

  Service Literature

Optional Equipment

• Air Inlet System

  90° adapter and straight adapters for air inlet to turbocharger Air cleaners Air cleaners with Cat dry paper filter elements (approximately 99.9% efficient at filtering SAE fine dust) Soot filter

• Control System

  4-20 mA load feedback signal Load sharing module Direct rack module

• Cooling System

  Separate Circuit Aftercooler (SCAC) Customer water connections Jacket water thermostats AC/OC thermostats Accessory module-mounted high volume expansion tank Jacket water heater Heat recovery connections and thermostats for use with water maker system ANSI connection adapters

• Exhaust System

  Exhaust manifold shields Vertical or 30° outboard exhaust orientation options Exhaust outlet expanders and weld flanges

• Fuel System

  Manual fuel priming pump Duplex primary fuel strainer Flexible fuel hose connections

• Lube System

  Dry engine-mounted sump system that gravity feeds into base assembly integral sump Engine-mounted duplex oil filter Intermittent air prelube Continuous electric prelube Redundant prelube with continuous electric prelube and intermittent air prelube backup Oil pan drain valves Electric continuous prelube pump Lube oil heater

• Protection System

  Wiring meets MCS requirements Upgrade PLC monitor to industrial PC Upgrades AC/OC, JW and start air pressure from contactors to transducers Raw water/sea water pressure transducer Modbus communication Beacon and horn Single engine remote display monitor Emergency pump start signal Cabinet cooler Generator power monitoring Remote relay panel Turbocharger speed sensors Cylinder pressure relief valve Oil mist detector Flywheel and damper guards

• Mounting System

  Base aseembly Vertically-restrained vibration isolators and weld plates

• Starting System

  Single turbine air starters Boost control valve for extremely cold ambient conditions Air start pressure reducing valves

• General

  Torsional couplings Mounting groups for engine, generator, and base Accessory module to mount attachments such as the expansion tank, heat exchanger, instrument panel and engine controls, annunciator panel, alarm and shutdown contactors, fuel strainer Flywheel Engine barring device options: One-year storage preservation Oceanic transportation shipping protection (shrink wrap and tarp) Engine testing — certified dynamometer test, fuel consumption test, rated speed performance test, overload test, minimum power setting, peak firing pressure test, turbo work cert and crankshaft work cert Standard and project-specific witness testing Spare parts kit

• Literature

  Project-specific installation drawings Electrical schematics and P&ID drawings