The Cat® 920 Small Wheel Loader features an optimized Z-bar linkage that combines the digging efficiency of a traditional Z-bar loader with tool carrier capabilities for great performance and versatility. With parallel lift and high tilt forces throughout the working range you can safely and confidently handle loads with precise control. A new engine layout greatly improves rear visibility and service access.
| Maximum Gross Power | 121hp |
| Rated Net Power - Rated Engine Speed | 2200r/min |
| Maximum Gross Power - Rated Engine Speed | 2200r/min |
| Rated Net Power - SAE J1349 | 120hp |
| Maximum Gross Power - ISO 14396 (metric) | 122hp |
| Rated Net Power - ISO 9249 | 118hp |
| Maximum Gross Torque - SAE J1995 | 372ft·lbf |
| Maximum Gross Torque - ISO 14396 | 369ft·lbf |
| Maximum Net Torque - SAE J1349 | 366ft·lbf |
| Maximum Net Torque - ISO 9249 | 363ft·lbf |
| Displacement | 220in³ |
| Bore | 3.85in |
| Stroke | 4.72in |
| Engine Model | Cat C3.6 |
| Emissions | Engine meets Tier 4 Final/Stage V emission standards. |
| Note | Net power advertised is the power available at the flywheel plus front drive implement pump when the engine is equipped with fan, air cleaner, muffler and alternator. |
| Maximum Gross Power - ISO 14396 | 121hp |
| Operating Weight | 21742lb |
| Bucket Capacities | 1.3-3.5 m3 (1.7-4.6 yd3) |
| Bucket Capacities - General Purpose | 1.3-1.9 m³ (1.7-2.5 yd³) |
| Bucket Capacities - Light Material | 2.5-3.5 m³ (3.3-4.6 yd³) |
| Recyclability | 95% |
| Transmission | 0.8gal (US) |
| Engine Crankcase | 2.6gal (US) |
| Diesel Exhaust Fluid (DEF) Tank | 4.8gal (US) |
| Axles - Rear | 4.5gal (US) |
| Cooling System | 5.7gal (US) |
| Hydraulic System - Including Tank | 25.9gal (US) |
| Axles - Front | 4.5gal (US) |
| Fuel Tank | 43.6gal (US) |
| Hydraulic Tank | 14.5gal (US) |
| Note | DEF used in Cat Selective Catalyst Reduction (SCR) systems must meet the requirements outlined in the International Organization for Standardization (ISO) standard 22241-1. |
| ROPS | ISO 3471:2008 |
| FOPS | ISO 3449:2005 |
| Note (3) | The labelled sound power level for the CE marked configurations when measured according to the test procedure and conditions specified in 2000/14/EC (as amended by 2005/88/EC) is 103 dB(A). |
| Note (2) | The declared dynamic operator sound pressure levels per ISO 6396:2008*, when the cab is properly installed and maintained, is 77 dB(A). |
| Note (1) | Cab and Rollover Protective Structures (ROPS) are standard in North America and Europe. |
| Note (4) | *The measurements were conducted with the cab doors and windows closed. |
| Maximum Working Pressure - Steering Pump | 3190psi |
| Steering Cycle Times - Full Left to Full Right - At 2,350 rpm: 90 rpm Steering Wheel Speed | 2.3s |
| Steering Articulation Angle - Each Direction | 40° |
| Number of Steering Wheel Turns - Full Left to Full Right or Full Right to Full Left | 3.4turns |
| Maximum Flow - Steering Pump | 21.7gpm |
| Relief Pressure - Tilt Cylinder | 4641psi |
| Maximum Flow - Implement Pump - 3rd Function, Maximum Flow, Standard | 25gpm |
| Maximum Flow - Implement Pump | 43.6gpm |
| Relief Pressure - Tilt Cylinder - 4th Function Relief Pressure | 4641psi |
| Hydraulic Cycle Time - Float Down, Maximum Lift to Ground Level | 2.7s |
| Note | All cycle times listed are with cylinder snubbing turned off. |
| Maximum Working Pressure - Implement Pump | 4061psi |
| Hydraulic Cycle Time - Total Cycle Time | 11.5s |
| Hydraulic Cycle Time - Rackback | 2.2s |
| Maximum Flow - Implement Pump - 4rd Function, Maximum Flow | 25gpm |
| Hydraulic Cycle Time - Dump, at Maximum Reach | 1.8s |
| Hydraulic Cycle Time - Raise, Ground Level to Maximum Lift | 4.8s |
| Maximum Flow - Implement Pump - 3rd Function, Maximum Flow, High | 40gpm |
| Note | *Creeper Control allows speed control from a stand still up to 10 km/h (6.3 mph). The Creeper Control will only work in Range 1. |
| Forward and Reverse - Speed Range 3 | 25mile/h |
| Forward and Reverse - Speed Range 2* | 12.5mile/h |
| Forward and Reverse - Speed Range 1* | 6.3mile/h |
| Rear | Oscillating ±11 degrees; Locking differential (standard) |
| Front | Fixed; Locking differential (standard) |
| Other Choices Include | 17.5 R25 L3 XHA2; 20.5 R25 L3 XHA3; 17.5-25 L2/L3 SGL; 20.5-25 L2/L3 SGL; 17.5-25 L3 HRL D/L-3A; 17.5 R25 L2 Snow; 20.5 R25 L2 Snow; 17.5 R25 Solid |
| Standard Size | 17.5 R25 L2 XTLA |
| Note (1) | Other tire choices are available. Contact your Cat dealer for details. |
| Note (3) | Caterpillar recommends that you consult a tire supplier to evaluate all conditions before selecting a tire model. |
| Note (2) | In certain applications, the loader’s productive capabilities may exceed the tire’s tonnes-km/h (ton-mph) capabilities. |
Print
Email
your location
call us
contact us