The AP1000F is a high-production wheel paver that excels on airports runways, interstates, highways, and other large jobsites. It's high travel speed, optional front wheel assist, and all-wheel drive features deliver superb mobility.
Operating Weight - With SE60 V 41985 lb
Standard Paving Range 3.0-6.0 m (9' 10" - 19' 6")
Operating Height - With Canopy 157 in
Operating Height - Without Canopy 146 in
Operating Width - Low Entry Hopper 142 in
Operating Width - Standard Entry Hopper 132 in
Hopper Capacity - Standard Entry 267 ft³
Inside Turn Radius 1.5 ft
Maximum Paving Speed - With Tamper Bar Screed 82 ft/min
Maximum Paving Speed - With Vibratory Screed 250 ft/min
Maximum Travel Speed 12 mile/h
Gross Power 225 HP
Engine Model Cat C7.1 with ACERT
Transport Length - With SE60 V Screed 22.1 ft
Transport Width - With End Gates Folded 9.83 ft
Transport Width - With Screed End Gates 10.66 ft
Truck Entry Height - With Low Entry Hopper 21 in
Truck Entry Height - With Standard Entry Hopper 22.5 in
Service Refill Capacities
Fuel Tank Capacity 92 gal (US)
Operating Length - With SE60 V Screed 22.5 ft
Operating Length - With SE60 V XW Screed 23.1 ft
Transport Height - Canopy Retracted 10.1 ft
Transport Height - Without Canopy 9.83 ft
Transport Length - With SE60 XW-Series 22.6 ft
Hopper Capacity - Low Entry Hopper 286 ft³
Maximum Paving Width - SE60 V Screed 25 ft
Maximum Paving Width - SE60 V XW, VT XW Screed 25 ft
Maximum Throughput Capacity 1766 tonnes/hr
Service Refill Capacities
DEF Tank 5 gal (US)
Operating Weight - With SE60 V XW 43472 lb
Operating Weight - With SE60 VT XW 45419 lb
Tractor Operating Weight 34820 lb
Tractor Shipping Weight 34228 lb
BENEFITS & FEATURES
Fuel Efficient and Quiet
Cat C7.1 Engine
The C7.1 engine provides 168 kW (225 hp) at 2200 rpm and meets U.S. EPA Tier 4 Final and EU Stage IV emmision standards.
Eco-mode utilizes an engine speed of 1650 rpm and reduces fuel burn by up to 5% over Cat E-series pavers while also lowering sound levels even more.
Automatic Engine Speed Control
When automatic engine speed control is activated, the engine speed is reduced to an idle speed of 1000 rpm when the propel lever is moved to neutral, or to 1300 rpm when screed heat is active.
Eco-mode and automatic engine speed control when activated together modify the engine rpm based on load factors. When activated the engine will operate at 1650 rpm when paving. If the upper power threshold is exceeded, the engine speed will increase to 2200 rpm and remain there until the demand drops below the threshold and remains there for 30 seconds, ensuring reliable performance.
Quiet heat mode operates at an engine speed of 1300 rpm and provides heating in under 15 minutes.
Quick heating mode provides a heat-up time in under 35 minutes when equipped with the 10 m (33 ft) wide-width paving package.
Three preset heating options provide a wide range of temperatures for various mix designs; Low is 110 degrees C or 230 degrees F, medium is 130 degrees C or 266 degrees F, high is 160 degrees C or 320 degrees F.
Better Visibility, Exceptional Comfort
The dual independent operating stations can extend beyond the frame for good all-around visibility. The low profile, front-mounted cooling system improves forward viewing and the redesigned auger assembly optimizes visibility to material height in front of the screed. The heated seat option, multiple seat adjustments, and tilting consoles conform to the operator to provide day-long comfort. Also, the top-mounted cooling system directs fumes, hot air, and fan noise away from the crew for a cooler and quieter working environment.
Fumes Management System
The exclusive ventilation system draws fumes from the conveyor tunnel as well as the auger chamber and redirects them away from the operator for a more comfortable working environment.
Water Resistant Displays
Single Touch Operation
Single touch features for the auto-fill feeder system, feeder system activation, and hopper control, allow operators to concentrate on truck exchanges and other duties for improved efficiency.
Technology helps operators perform. Intuitive symbols and large graphics simplify operation., while the interactive LCD display with touchscreen access to generator activation, screed temperature control, and mix height adjustment, increase efficiency.
More Efficient Delivery
Auto-Fill Feeder System
The auto-fill system simplifies starts by alternating the conveyors and augers until the mix height reaches the sensor point.
Single Touch Feeder System
The single touch feeder system automatically activates the entire feeder system with a single button for better efficiency.
One Touch Hopper Control
The hopper wings and hydraulic apron can be folded with a single touch and release. The system can be tailored to activate left or right wings, or the front hydraulic apron independently or together.
Cleanout and Warm-Up Mode
This feature activates the augers, conveyors, and tamper-bar (if equipped) at a reduced speed, allowing the application of release agents to prevent material build-up.
Mix Height Adjustment
Mix height adjustment in front of the screed can be modified from the tractor LCD display for increased versatility when needed.
Hydraulic Mainframe Extensions
The optional 457 mm (18") hydraulic mainframe extensions attach to the auger assembly and provide smooth material flow out to the extenders. They retract with the screed extensions when reducing paving widths.
Multiple Feed Sensor Options
The feeder system can be tailored to automatically operate with 0, 2, or 4 feed sensors. When paving with 0 sensors due to a failure, simply set the feeder system to automatic and adjust the mix height setting, no need to cycle the manual switch as previous models required.
Hardware-free bed plates simplify replacement and bottom side mounting hardware for the chain guards eliminates bolt wear and material build-up for easier replacement.
Power Turning System
A postion sensor located in the left steering cylinder helps maintain consistent travel speeds when making turns by adjusting the drive speed of the propel motors according to the steering angle of the front wheels. This unique system leads to better mat quality and less wear on the drive system.
Provides power to the front bogie wheels for additional traction. A dedicated pump delivers a 50% increase in torque over previous models.
Provides power to the front and rear bogie wheels. It delivers a 200 % increase in pull force over the previous models.
Screed Heat Technology
Exclusive zone monitoring allows heating to continue in the event of a temperature sensor failure. The system also monitors heating elements for failure conditions, eliminating unnecessary replacement.
Feeder system ratio adjustment capability from the screed provides versatility. Standard hydraulic adjustment for extender height, slope, and crown, allows for on-the-go adjustment at standard and maximum paving widths.
Two-Speed Proportional Extender Control
Exclusive two-speed proportional extender control provides slower speed for precise control around obstacles and quick reaction when extending paving widths.
The heating elements slide out for easy replacement, no need to remove the screed plates. Machined screed frames simplify plate replacement and leveling.
Tamper Bar Screed Option
Tamper bar equipped screeds increase density as it tucks material under the screed plates. Three stroke settings of 2, 4, and 7 mm combine with a variable tamper speed of 0 to 1800 rpm to provide versatility.
Wide-Width Paving Packages
Exclusive power controls simplify adjustment across the entire 10 m (33 ft) paving width for better mat texture and quality. An innovative hooking system utilizes extender slope to attach wide-width paving packages, eliminating the need for additional lifting devices.
Cat Grade Control
F-Series pavers allow Cat Grade Control to be operated from any of the two tractor or two screed consoles. Split screen mode can be setup to monitor each side of the screed allowing a single person to monitor operation.
More accurate control, maximizes mix utilization, saves money. True averaging with sonic sensors that utilize 5 transducers, 2 readings are discarded and 3 averaged. A 10-point Auto-Calibration procedure eliminates over/under adjustment from a single calibration point. Cross-coupling, slope and elevation are maintained with height adjustments. The true 9 m (30 ft) sonic averaging beam modifies tow point movement by 1/3 of total grade deviation.
Water-resistant displays, factory installed components, and consistent routing deliver performance. Sealed components withstand heat, moisture, and vibration, and the built-in temperature sensors provide better reliability than bail-type sensors.
- Air-ride Seat with Heat
- All-Wheel Drive
- Auger and Mainframe Extensions
- Auxiliary Power Panel
- Cat Grade Control
- Decelerator Pedals
- Ecological Washdown System
- Feed Sensor (Sonic or Mechanical)
- Front Wheel Assist
- Hardtop Canopy
- HID Lights
- Leveling Devices
- Lights (Working or Roading)
- Mainframe Extensions (Power or Manual)
- Power Folding Front Apron
- Product Link
- Oscillating Push Rollers
- Steering Guide
- Tow Point Indicators (Upper)
- Truck Hitch
- Uptime Kit
- Ventilation System
- Warning Beacon
- Wide-width Paving Packages
- Windshield w/Hardtop Canopy
- Non-Contacting Sonic Grade Sensor
- Contacting Grade Sensor
- Outboard Leveler, 9.15 m (30') and 12.2 m (40')
- Inboard Leveler
- Mobile Stringline
- Fore ‘N Aft Leveler
- Sonic Averaging Beam
- Rigid Ski, 9.15 m (30') and 12.2 m (40')
- SE60 V Vibratory Screed
- SE60 V XW Vibratory Screed
- SE60 VT XW Vibratory and Tamper Bar Screed
CALL NOW TO LEARN MORE
865-595-1060 or 865-599-8225
865-595-1060 or 865-599-8225
HOW CAN WE HELP?
SHARE YOUR FEEDBACK OR ASK A QUESTION