C32 IMO III

Cat C32 Auxiliary / Diesel Electric Propulsion Engine (IMO III)

C32 IMO III
DETAILS

SPECIFICATIONS
Power Rating
Minimum Rating 352 BHP
Maximum Rating 1172 BHP


Engine Specifications
Aspiration Turbocharged-aftercooled aspiration
Bore 5.71 in
Configuration Vee 12, 4-stroke-cycle diesel
Displacement 1959 in³
Rotation Counterclockwise from flywheel end
Stroke 6.38 in


Dimensions & Weights
Maximum Engine Dry Weight 7160 lb
Maximum Height 63.5 in
Maximum Length 89.8 in
Maximum Width 57.3 in
Minimum Engine Dry Weight 6950 lb
Minimum Height 59.3 in
Minimum Length 83.9 in
Minimum Width 57.1 in


Engine Specifications
Emissions IMO III emissions certified (SCR required)


Clean Emissions Module (CEM) - Dimensions
6 Brick U-Flow - Height 23.5 in
6 Brick U-Flow - Length 85 in
6 Brick U-Flow - Weight 1235 lb
6 Brick U-Flow - Width 56.9 in
6 Brick Z-Flow - Height 23.5 in
6 Brick Z-Flow - Length 147.7 in
6 Brick Z-Flow - Weight 1246 lb
6 Brick Z-Flow - Width 43.5 in
Dosing Cabinet - Height 22.8 in
Dosing Cabinet - Length 37.4 in
Dosing Cabinet - Weight 209 lb
Dosing Cabinet - Width 18.8 in


Engine Specifications
Cooling Heat exchanger or keel cooled
Flywheel Housing SAE No. 0 with SAE No. 18 flywheel (136 teeth)
Governor Electronic (A5 ECM)
Oil Change Interval 750 hrs - deep pan
Rated Engine Speed 1500 rpm
Refill Capacity Lube Oil System w/ oil filter change: 146 L (38.5 gal) - deep pan


BENEFITS & FEATURES
Emissions


Utilizes SCR Technology to enable IMO III emission regulations compliance while lowering operational costs

Control Strategy


Utilizes closed loop air assisted DEF dosing control strategy that delivers: Highest efficiency mixing and control to lower operational costs; Extends emissions useful life; Ensures compliance; Flexible to urea quality

Fuel System


Enhanced control of fuel injection optimized through crank timing and the A5 ECM technology

Power Reserve


Industry leading power reserve

Certifications


Wide range of available Marine Society certifications

Warranty


Industry-leading warranty coverage for factory packaged components

Service


Global dealer network for service in any location

EQUIPMENT
Standard Equipment

AIR INLET SYSTEM
  • Separate circuit aftercooled (SCAC)
  • Closed crankcase fumes disposal
CONTROL SYSTEM
  • 24V control system
COOLING SYSTEM
  • Heat exchanger or Keel Cooling
  • Watercooled exhaust manifold and turbocharger
  • Hard seawater lines – no flexible hoses
  • Flanges for cooling connections, ANSI or DIN
FUEL SYSTEM
  • Duplex fuel filters with hybrid fuel lines
  • Shipped loose primary fuel filter with water separator
  • Fuel transfer and priming pump
LUBE SYSTEM
  • Oil fill, simplex filter and dipstick
  • Deep or shallow sump oil pan
MOUNTING SYSTEM
  • Adjustable front support mounting system
GENERAL
  • Right or left hand service sides
  • Customer wiring and service tool connector

Optional Equipment

ALARM AND PROTECTION
  • MECP I control panel
  • MECP III control panel with Cat® Alarm and Protection System
EXHAUST SYSTEM
  • Water-in-fuel and exhaust temperature sensors
  • Muffler
CHARGING SYSTEM
  • Charging alternator
FUEL SYSTEM
  • Manual or electric fuel priming pump
  • Fuel cooler
LUBE SYSTEM
  • Duplex oil filters
POWER TAKE-OFFS
  • Front drives including stub shaft and pump drive
  • Rear SAE A or B pump drives
STARTING SYSTEM
  • Starting motors – air, electric or redundant