C32 ACERT™ (HAZARDOUS LOCATION)

Cat C32 ACERT hazardous location engines are the ideal solution for specialized and demanding operations in the oilfield. Engines are hazardous-location certified from the factory to minimize installation design, time, and cost. Decades of field operation and intense research and development allow Cat C32 ACERT hazardous location engines to deliver excellent performance with low operating costs and emissions. Hazardous location engines are certified to operate in potentially explosive environments. Applications powered by C32 ACERT engines include well stimulation pumping, pump skids, nitrogen units, acidizing units, blenders, and hydraulic power units. Cat engines are backed by the worldwide network of Cat dealers ready to support your operation with technical support, service, parts, and warranty. C32 ACERT hazardous location engines, with ratings 597-828 bkW (800-1110 bhp) @ 2100 rpm meet IMO Tier II, U.S. EPA Marine Tier 2, and U.S. EPA Non-road Tier 2 equivalent emission standards. They are available using U.S. EPA and EU Flexibility, and for other regulated and non-regulated areas.


SPECIFICATIONS
General Specifications
Minimum Rating 800 BHP
Maximum Rating 1110 BHP
Aspiration Turbocharged-Aftercooled
Displacement 1960 in³
Flywheel and Flywheel Housing SAE No. 0 or SAE No. 1
Flywheel Teeth 136
Stroke 6.4 in
Bore 5.7 in


Emissions
Emissions U.S. Non-Road Tier 2 CARB, IMO Tier II, EPA Marine Tier 2


Dimensions
Length 76.18 in
Width 56.34 in
Height 54.66 in
Weight 6950 lb


BENEFITS & FEATURES
Technology


- Electrical harness containing point-to-point wiring without splices in any power/signal wires - Electrical harnesses and connectors are overmolded and are routed through urethane tube for protection against impact and vertical flame propagation. - To meet safety requirements, connectors require the use of a special tool to be disconnected and bear the “do not disconnect while energized” warning. - Optional ATEX and NEC certified 25-foot customer harness - ECU is certified as part of the engine to restricted breathing per EN 60079-15. ECU is protected with a stainless steel guard. - Fuel injector connections at valve cover bases are protected with stainless steel guards

Advanced Digital Engine Management


ADEM A4 engine management system integrates speed control, air/fuel ratio control and ignition/detonation controls into a complete engine management system with integrated digital ignition, engine protection and monitoring.

Transmissions


The full line of Cat engine/transmission packages can be fully integrated with your axle, hydraulics, and operator interface. Cat transmissions deliver continuous operation under full load, smooth shifting at any speed, and maximum up time, with unmatched durability and easy maintenance.

Custom Packaging


Trust a Cat factory custom package to meet your exact petroleum application needs. Cat engines, generators, enclosures, controls, radiators, transmissions — anything your project requires — can be custom designed and matched to create a one-of-a kind solution. Custom packages are globally supported and are covered by a oneyear warranty after startup.

Full Range of Attachments


Large variety of factory-installed engine attachments reduces packaging time

Testing


Every engine is full-load tested to ensure proper engine performance.

Product Support Offered Through Global Cat Dealer


More than 2,200 dealer outlets Cat factory-trained dealer technicians service every aspect of your petroleum engine Cat parts and labor warranty Preventive maintenance agreements available for repairbefore-failure options S•O•S SM program matches your oil and coolant samples against Caterpillar set standards

Over 80 Years of Engine Manufacturing Experience


Ownership of these manufacturing processes enables Caterpillar to produce high quality, dependable products.

Over 80 Years of Engine Manufacturing Experience


Ownership of these manufacturing processes enables Caterpillar to produce high quality, dependable products.

Web Site


For all your petroleum power requirements, visit www.catoilandgasinfo.com.

Web Site


For all your petroleum power requirements, visit www.catoilandgasinfo.com.

EQUIPMENT
Standard Equipment

Air Inlet System
  • Dual side-mounted turbochargers — inlet 152.4 mm (6 in) hose connection
Control System
  • Programmable ratings
  • Cold mode start strategy
  • Automatic altitude compensation
  • Power compensation for fuel temperature
  • Programmable low and high idle
  • Electronic diagnostics and fault logging
  • Engine monitoring and protection system (speed, temperature, pressure)
  • J1939 Broadcast (diagnostic, engine status and control)
  • Electronic governing, PTO speed control
  • Certified electrical control system
  • Customer interface harness available as optional attachment
Cooling System
  • Thermostats and housing — outlet LH vertical orientation
  • Jacket water pump — gear-driven, centrifugal, RH
Exhaust System
  • Exhaust manifold, water-cooled
  • Dual turbo, rear turbo exhaust, full marmon connection 127 mm (5 in), maximum load 10 kg for direct connection to turbo
  • Water-cooled center sections
Flywheels and Flywheel Housing
  • Mandatory selection of: SAE No. 0 or SAE No. 1 flywheel and housing SAE standard rotation
Fuel System
  • MEUI fuel system
  • Fuel filter — RH (2 micron high performance)
  • Fuel transfer pump
  • Fuel priming pump
Lube System
  • Crankcase breather — rear-mounted
  • Oil cooler — RH
  • Oil filler in RH front gear case
  • Oil filter — RH
  • Oil level gauge — RH
  • Oil pan rear sump
Mounting System
  • Narrow front support
Power Take-Offs
  • Crankshaft pulley — 203.2 mm (8 in) 5 grooves 15.9 (.63 in) wide; 292.1 mm (11.5 in) 1 groove 15.9 (.63 in) wide
General
  • Paint — Cat yellow
  • Vibration damper with single pulley
  • Lifting eyes
  • Automatic variable timing — electronic
  • Electronic installation kit 70-pin connector (connectors, pins, socket)
Mandatory Options
  • HP must be specified when ordering
  • All engines shipped at 2100 rpm
  • Flywheel housing
  • These engines meet the current IMO emission standards as defined by Regulation 13 of Annex VI to the International Convention for the Prevention of Pollution from Ships, 1973, as modified by the Protocol of 1978, further amended by the Protocol of 1997. A statement of compliance issued by the United States government's EPA (Environmental Protection Agency) is included in the technical file that is shipped with the engine as proof of our engine's ability to meet IMO emissions requirements. If this technical file is insufficient to meet the customer's requirements, then a GL or CCS IMO emissions certification may be ordered.

Optional Equipment

Air Inlet System
  • Air cleaner
  • Air inlet adapters
  • Turbocharger outlet adapters
  • Air lines
Charging System
  • Battery chargers
  • Charging alternators
  • Alternator mounting
  • Circuit breakers and mountings
Cooling System
  • Dry charge coolant conditioners
  • Thermostat housing
  • Coolant level sensor
  • Radiator
  • Suction fans and blower fans
  • Fan adapters
  • Fan drives
Emissions
  • IMO certifications
Exhaust System
  • Elbows
  • Mufflers
Fuel Systems
  • Electric fuel priming pump
Instrumentation
  • Customer management device
  • Interconnect harness
  • Gauges and instrument panels
Lube System
  • Oil pans
  • Oil service side
  • Oil level gauge
  • Oil filters
  • Lubricating oils
Mounting System
  • Structural steel base
  • Engine support — front and rear
Power Take-Offs
  • Auxiliary drive
  • Damper pulley
  • Hydraulics gear pumps
Protection System
  • Mechanical shutoffs
  • Solenoid shutoffs
Starting System
  • Electric starting motors - 12V, 24V
  • Battery sets - 24V
  • Battery rack and cable
  • Starting aids
Transmission Arrangement
  • Transmission water lines
  • Transmission cooler