C18 ACERT™

Cat C18 ACERT™ Fire Pump Engines. Ratings: 447-597 bkW (600-800 bhp)@ 1800-1900 rpm meet U.S. EPA Tier 3 or U.S. EPA Tier 2 emission standards for stationary emergency fire pump engines. Rating: 522 bkW (700 bhp) @ 1500 rpm is Non-certified. FM Approved. UL Listed.


SPECIFICATIONS
Engine Specifications
Minimum Rating 600 BHP
Maximum Rating 800 BHP
Emissions U.S. EPA Tier, Tier 2 or non-certified
Rated Speed 1750 r/min
Bore 5.7 in
Stroke 7.2 in
Displacement 1106 in³
Aspiration Turbocharged-Aftercooled
Engine Weight - Net Dry 3900 lb
Oil Change Interval 500 h
Rotation from Flywheel End Counterclockwise
Flywheel and Flywheel Housing SAE No. 1
Flywheel Teeth 113


Capacity for Liquids
Lube Oil System - Refill 10 gal (US)
Cooling System - Engine 13.3 gal (US)


Dimensions
Length 74.4 in
Width 43 in
Height 54.3 in


BENEFITS & FEATURES
Emissions



Ratings--447 bkW (600 bhp) @ 1750, 1900, 2100 rpm and 522 bkW (700 bhp) @ 1900 and 2100 rpm--meet U.S. EPA Tier 3 emission standards for stationary emergency fire pump engines. FM approved. UL listed - U.S. and Canada. Meets NFPA 20 standards.
Ratings--597 bkW (800 bhp) @ 1750, 1900 and 3100 rpm--meet U.S. EPA Tier 2 emission standards for stationary emergency fire pump engines. FM approved. UL listed - U.S. and Canada. Meets NFPA 20 standards.

EQUIPMENT
Standard Equipment

Air Inlet System
  • Dual turbocharger: front and rear inlet 127.mm (5.0 in)
  • Separate Circuit Aftercooled (SCAC)
Charging System
  • Charging alternator 24 volt, 50 amp
Control System
  • Dual Electronic Control Units (ECU), primary and secondary
  • Electronic governing, PTO speed control
  • Programmable ratings
  • Cold start capability to -20° C (-4° F)
  • Automatic altitude compensation
  • Power compensation for fuel temperature
  • Programmable low and high idle and total engine limit
  • Electronic diagnostics and fault logging
  • Engine monitoring system SAE J1939 broadcast and control
Cooling System
  • Thermostats and housing, vertical outlet
  • Jacket water pump, centrifugal
  • Heat exchanger installed
  • Expansion tank
Exhaust System
  • Exhaust manifold, dry
  • Dual turbo: exhaust elbow, dry 203 mm (8 in)
Flywheels and Flywheel Housing
  • SAE No. 1 flywheel
  • SAE No. 1 flywheel housing
  • Power take-off (PTO) flywheel stub shaft
Fuel System
  • Electronic unit injector
  • Fuel filter, secondary (2 micron high performance)
  • Fuel transfer pump
  • Fuel priming pump
  • Fuel sample valve, mounted on fuel filter base
  • Primary fuel filter
  • Water separator
Instrumentation
  • Instrument panel, LH
  • Engine oil pressure gauge
  • Voltmeter gauge
  • Water temperature gauge
  • Tachometer/engine hour meter
Lube System
  • Open crankcase ventilation system
  • Oil cooler
  • Lube oil filter
  • Front sump oil pan
  • Oil filler
  • Oil dipstick
  • Oil pump
Mounting System
  • Front and rear support
Protection System
  • Stop-Start System, automatic (compatible with NFPA 20 requirements, able to be energized from either of two battery sources and capable of manual starter actuation)
Starting System
  • 24 volt, LH electric starting motor
  • Jacket water heater (3 kW, 120-240 volt)
General
  • Vibration damper
  • Lifting eyes
  • Automatic variable timing, electronic
  • Electronic installation kit, 70 pin connector (connectors, pins, sockets)


HOW CAN WE HELP?
SHARE YOUR FEEDBACK OR ASK A QUESTION
Feel free to ask a question or share a comment about the information on this page.

To help us answer your question or respond to your comment, please enter your email address.