C175-16 (50 HZ)

Caterpillar is leading the power generation marketplace with Power Solutions engineered to deliver unmatched flexibility, expandability, reliability, and cost-effectiveness.


SPECIFICATIONS
Generator Set Specifications
Minimum Rating 2500 kVA
Maximum Rating 3100 kVA
Emissions/Fuel Strategy Low Fuel Consumption, Low Emissions
Voltage 380 to 11000 Volts
Frequency 50 Hz
Speed 1500 rpm
Duty Cycle Standby, Mission Critical, Prime, Continuous


Engine Specifications
Engine Model C175-16 SCAC, V-16, 4-Stroke Water-Cooled Diesel
Bore 6.89 in
Stroke 8.66 in
Displacement 5166.88 in³
Compression Ratio 16:07:01
Aspiration Turbo Aftercooled
Fuel System Common Rail
Governor Type ADEM™ A4


Generator Set Dimensions
Length - Minimum 241.6 in
Length - Maximum 311 in
Width - Minimum 83 in
Width - Maximum 108.5 in
Height - Minimum 87 in
Height - Maximum 130.2 in
Dry Weight - Genset (minimum) 42750 lb
Dry Weight - Genset (maximum) 50750 lb


BENEFITS & FEATURES
Cat Generator Set Package


Cat Generator Set Package
  • Cat generator set packages have been fully prototype tested
  • Accepts 100% block load in one step and meets other NFPA 110 loading requirements
  • Conform to ISO 8528-5 steady state and transient response requirements

  • Cat Diesel Engine


    Cat Diesel Engine
  • Reliable, rugged, durable design
  • Field-proven in thousands of applications worldwide
  • Four-stroke-cycle diesel engine combines consistent performance and excellent fuel economy with minimum weight

  • SR5 Alternator


    SR5 Alternator
  • Superior motor starting capability minimizes need for oversizing alternator
  • Designed to match performance and output characteristics of Cat diesel engines
  • Robust Class H insulation

  • EMCP 4 Control Panel


    EMCP 4 Control Panel
  • User-friendly interface and navigation
  • Scalable system to meet a wide range of installation requirement
  • Expansion modules and site-specific programming for specific customer requirements

  • Cooling System


    Cooling System
  • Designed to operate in standard ambient temperatures up to 50°C (122°F)
  • Contact your Cat Dealer for specific ambient and altitude capabilities

  • Certifications


    Certifications
  • IBC Seismic Certification
  • EU Certification of Conformance (CE)
  • EEC Declaration of Conformity

  • One Safe Source


    One Safe Source
  • Components used in the generator set are selected at the design stage to provide optimum package performance
  • The generator set is fully assembled at a Caterpillar facility following our quality guidelines
  • Each generator set package is tested before leaving the Caterpillar facility
  • Cat product support, including dealer service, parts and warranty covers the entire Cat power system

  • World Wide Product Support


    World Wide Product Support
  • Cat dealers have over 1,800 dealer branch stores operating in 200 countries
  • Your local Cat dealer provides extensive post-sale support, including maintenance and repair agreements

  • EQUIPMENT
    Standard Equipment

    Air Inlet System
    • 4 x Single element canister with service indicator(s)
    Control Panel
    • EMCP4 / EMCP4.2
    • Engine cool-down timer.
    • Frequency (Hz)
    • RPM
    • Lamp test
    • True RMS AC metering, 3-phase, +/-2% accuracy
    • Failure to start (overcrank)
    • Controls
    • Alarm acknowledge
    • Speed adjust
    • Digital Indicators
    • 4 Programmable relay outputs (Form A)
    • Coolant temperature
    • Oil pressure (psi, kPa or bar)
    • Programmable Protective Relaying Functions
    • Reverse power
    • Volts (L-L & L-N)
    • Overspeed
    • Emergency stop pushbutton
    • Overcurrent
    • 2 Programmable relay outputs (Form C)
    • Reverse Reactive Power
    • Low coolant level
    • Serial annunciator module data link
    • Communications
    • 6 Programmable digital inputs
    • Text alarm / event descriptions.
    • Warning / shutdown Indicators
    • Amps (per phase & average)
    • Accessory module data link
    • Customer data link (Modbus RTU)
    • Low coolant temperature
    • 24 Volt DC operation
    • Over / under voltage
    • High coolant temperature
    • Engine cycle crank
    • Generator mounted - rear facing
    • Emergency stop
    • 2 Programmable digital outputs
    • Power Factor (per phase & average)
    • Auto / start / stop control.
    • Generator phase sequence
    • Operating hours
    • Over / under frequency
    • Environmental sealed front face.
    • DC Volts
    • Low oil pressure
    Cooling System
    • SCAC cooling
    • Coolant Sensors
    • Coolant drain line and valves
    • Radiator group - shipped loose
    • Fan and belt guards
    Exhaust System
    • Bolted flange, with bellow for each turbo
    • Dry Exhaust Manifold
    Fuel System
    • Filters x 3
    • Secondary / Tertiary fuel filters
    • 4 Micron Spin On Type
    • 10 Micron Spin On Type
    • Primary fuel filter water / fuel water separator
    • Engine mounted filters X3
    Generator and Attachments
    • 6 Leads
    • IEC Platinum stator RTDs
    • Voltage Regulator
    • Voltage regulator
    • Reactive droop capability
    • 3 Phase voltage sensing
    • RFI suppression
    • Min / max exciter limiter
    • exciter diode monitor
    • Form Wound
    • Permanent magnet
    • NEMA Class H insulation
    • Class H temperature rise at 40C ambient
    • (LV) Busbar connections, top/center mounted, top cable entry
    • Salient pole
    • 3 Phase Brushless
    • 50 Hz models: IEC standard hole pattern
    • (MV) Busbar connections, right side extension box, bottom cable entry
    • Anti condensation space heater
    • Class F temperature rise at 40C ambient
    • Right side extension box, bottom cable entry
    Governing System
    • ADEM A4
    • Redundant shutdown (Overspeed protection through a duplicate speed sensing system)
    Lube System
    • Oil filter, filler and dipstick
    • Integral lube oil cooler
    • Oil drain lines and valve
    • Gear type lube oil pump
    • Fumes disposal
    • Lubricating oil
    • Prelube - required with prime, continuous, and standby
    Mounting Systems
    • Battery disconnect switch
    • Rubber anti-vibration mounts (shipped loose)
    • Batteries and battery rack w/cables
    • Dual 24 volt electric starting motors
    • Rails - Engine / generator
    Service Instructions
    • Two PM inspections
    Power Termination
    • Bus Bar
    General
    • Paint - Caterpillar yellow with high gloss black rails & radiator
    • Right hand service
    • Flywheel and flywheel housing-SAE No. 00
    • SAE standard rotation

    Optional Equipment

    Air Inlet System
    • Single element air cleaner
    • Dual element air cleaner
    • Air inlet adapters
    • Air inlet protection
    Control Panel
    • EMCP 4.3, EMCP 4.4
    • EMCP 4.4 optional harness
    • EMCP and MV&HV power connection locations
    • Load share module
    • EMCP mounting location - LV / MV
    • Customer AC-DC connection mounting location - LV/MV
    • Load share module / auxiliary plate and auxiliary box (LV)
    • Load share governor
    • Frame boxes
    • Automatically selected ground
    • EMCP voltage and current sensing groups
    • Raise lower switch
    • Speed adjust
    • Annunciator modules
    • Customer interface options
    • Generator temperature monitoring
    • Modbus monitoring of packages
    • E-Stop
    • Interconnect harness
    • Generator Harness
    Cooling System
    • Package mounted radiator
    • Remote radiators
    • Fuel cooler
    Exhaust System
    • Front housing - Standby or mission critical
    • Front housing - Prime or continuous
    • Exhaust collectors / Manifold
    • Exhaust support group
    • Mufflers
    • Weld flanges
    • Aftercooler drain
    Crankcase Systems
    • Explosive relief valves
    • Crankcase ventilation system
    Fuel System
    • Primary fuel filter
    Generators and Attachments
    • Low voltage - 1800 and 3000 Frames - 50 Hz, 3 phase, 1500 rpm, FW, PM, No of leads=6, Pitch 0.6667
    • Medium Voltage - 1800 and 3000 Frames - 50 Hz, 3 phase, 1500 rpm, FW, PM, No of leads=6, Pitch 0.6667
    • Low Voltage - 1800 and 3000 Frames - 60 Hz, 3 phase, 1800 rpm, FW, PM, No of leads=6, Pitch 0.6667
    • Space heater kit
    • Thermostat for space heater
    • Conversion GP-Top cable entry
    • Generator air intake
    • Differential current transformers
    Instrumentation
    • Pyrometer and thermocouples
    Lube System
    • Lube oil heater
    • Drain group oil pans
    • Lubricating oil
    • Electric prelube pumps
    • Oil filters
    Mounting
    • Rubber anti-vibration mounts
    • Spring type linear vibration isolators
    • IBC vibration isolators - Shipped loose
    Power Connections
    • Center post busbars (LV)
    • Side / Rear mounted busbars (LV)
    • Harnesses (Breaker)
    • Cable entry options (LV)
    • Enclosures - Control packaging (LV)
    • Power connection covers (LV)
    • Neutral ground (LV)
    • 1800 Frame generators circuit breaker
    • Masterpack breakers
    • Paralleling circuit breakers
    • 1800 Frame generator side / rear mounted busbars (MV)
    • Cable entry options (MV)
    • Neutral ground (MV)
    • Low voltage connection cable
    • Masterpack breaker connections
    Special Tests / Reports
    • Generator test report
    • PGS test report @ 1.0 power factor
    • PGS test report @ 0.8 power factor
    • Standard genset TVA (Torsional Vibration Analysis) report
    • Custom genset TVA report
    • Special test charge - Engine only
    • Genset fuel consumption test
    • Standard engine test charge
    • IBC seismic certification
    • OSCOSH1 seismic certification
    Starting / Charging System
    • 24 Volt power distribution box
    • 24 Volt electric starting motors
    • Air starting motor
    • Air pressure regulator
    • Starter location covers
    • 24 Volt battery sets - Dry
    • Heavy duty battery sets with rack
    • 20 Amp battery chargers
    • 35 Amp battery chargers
    • 50 Amp battery chargers
    • Charging alternators - Dry
    • Jacket water heaters
    • Jacket water heater wiring groups
    General
    • Special paint colors
    • Service tools - Engine barring group
    • Barring group manual
    • Engine barring air powered
    • Control GP - Air powered bar group

    CALL NOW TO LEARN MORE

    Andy Downs
    423-463-2131 or 423-698-6943

    Neal Reinhardt
    865-595-1034 or 865-771-1036