950M (TIER 4/STAGE IV) (2016)

The new 950M Wheel Loader has a U.S. EPA Tier 4 Final/EU Stage IV ACERT™ engine equipped with a combination of proven electronic, fuel, air and aftertreatment components. Applying proven technologies systematically and strategically lets us meet our customer’s high expectations for productivity, fuel efficiency, reliability and service life. Deep system integration results in reduced emissions, improved performance and improved fuel economy without interrupting machine performance making it seamless to operators. M Series Loaders are 10% more fuel efficient than the K Series Loaders and up to 25% more efficient than the H Series Loaders they replace. (Fuel efficiency is measured in mass of material moved per volume of fuel burned. Average efficiency improvement as tested and analyzed for an average composite cycle and stand configuration with variations per comparable model with and without economy mode active. Factors influence result variation such as, but not limited to, machine configuration, operator technique, machine application, climate, etc.) Optional configurations are available. (Optional configuration and equipment may vary from region to region. Consult your Caterpillar representative for further details.)


SPECIFICATIONS
Engine
Net Power – ISO 9249 230 hp
Engine Model Cat C7.1 ACERT
Max Gross Power @ 2,100 rpm – SAE J1995 250 hp
Max Gross Power @ 2,100 rpm – ISO 14396 249 hp
Displacement 428 in3
Max Gross Power @ 2,100 rpm – ISO 14396 (metric) 253 hp
Max Net Power @ 2,100 rpm – SAE J1349 230 hp
Max Net Power @ 2,100 rpm – ISO 9249 230 hp
Max Net Power @ 2,100 rpm – ISO 9249 (metric) 232 hp
Peak Gross Torque (1,300 rpm) – SAE J1995 911 lbf-ft
Peak Gross Torque (1,300 rpm) – ISO 14396 908 lbf-ft


Weights
Operating Weight 42357 lb


Buckets
Bucket Capacities 2.5-9.2 m³ (3.3-12.0 yd³)


Hydraulic System
Hydraulic Cycle Time – Total 8.9 Seconds
Implement Pump Type Variable Axial Piston
Implement System: Maximum Pump Output (2,150 rpm) 76 gal/min
Implement System: Maximum Operating Pressure 4250 psi


Service Refill Capacities
Cooling System 15.6 gal
Crankcase 5.8 gal
Transmission 11.4 gal
Differentials and Final Drives – Front 11.4 gal
Differentials and Final Drives – Rear 11.4 gal
Hydraulic Tank 33.0 gal
DEF Tank 4.2 gal
Fuel Tank 72.6 gal


Transmission
Forward 1 4.3 mph
Forward 2 7.5 mph
Forward 3 12.0 mph
Forward 4 16.0 mph
Forward 5 24.5 mph
Reverse 1 4.3 mph
Reverse 2 7.5 mph
Reverse 3 16.0 mph


Operating Specifications
Breakout Force 40690 lbf
Static Tipping Load – Full 40° Turn – No Tire Deflection 25926 lb
Static Tipping Load – Full 40° Turn – with Tire Deflection 24262 lb


Sound
With Cooling Fan Speed at Maximum Value: Operator Sound Pressure Level (ISO 6396:2008) 70 dB(A)
With Cooling Fan Speed at Maximum Value: Exterior Sound Power Level (ISO 6395:2008) 108 dB(A)
With Cooling Fan Speed at Maximum Value: Exterior Sound Pressure Level (SAE J88:2013) 75 dB(A)*


Engine
Maximum Net Torque (1,300 rpm) 858 lbf-ft


Weights
Note Weight based on a machine configuration with Michelin 23.5R25 XHA2 L3 radial tires, full fluids, operator, standard counterweight, cold start, roading fenders, Product Link, manual diff lock/open axles (front/rear), power train guard, secondary steering, sound suppression and a 3.1 m3 (4.1 yd3) general purpose bucket with BOCE.


Bucket Capacities
Bucket Range 2.5-9.2 m³ (3.3-12.0 yd³)


Transmission
Note Maximum travel speed in standard vehicle with empty bucket and standard L3 tires with 787 mm (31 in) roll radius.


Sound
Note *Distance of 15 m (49.2 ft), moving forward in second gear ratio.
With Cooling Fan Speed at 70% of Maximum Value: Operator Sound Pressure Level (ISO 6396:2008) 69 dB(A)
With Cooling Fan Speed at 70% of Maximum Value: Exterior Sound Power Level (ISO 6395:2008) 106 LWA**
Note **European Union Directive “2000/14/EC” as amended by “2005/88/EC.”


Operating Specifications
Note For a machine configuration as defined under “Weight.”
Note Full compliance to ISO 143971:2007 Sections 1 thru 6, which requires 2% verification between calculations and testing.


Dimensions – Standard Lift
Height to Top of Hood 8.83 ft
Height to Top of Exhaust Pipe 11.17 ft
Height to Top of ROPS 11.33 ft
Ground Clearance 1.17 ft
Center Line of Rear Axle to Edge of Counterweight 6.33 ft
Center Line of Rear Axle to Hitch 5.50 ft
Wheelbase 11.00 ft
Overall Length (without bucket) 22.67 ft
Hinge Pin Height at Carry Height 2.08 ft
Hinge Pin Height at Maximum Lift 13.25 ft
Lift Arm Clearance at Maximum Lift 10.75 ft
Rack Back at Maximum Lift 59 degrees
Rack Back at Carry Height 49 degrees
Rack Back at Ground 36 degrees
Maximum Width over Tires (loaded) 9.25 ft
Tread Width 7.00 ft
Note All dimensions are approximate and based on Michelin 23.5R25 XHA2 L3 radial tires.


Dimensions – High Lift
Height to Top of Hood 8.83 ft
Height to Top of Exhaust Pipe 11.17 ft
Height to Top of ROPS 11.33 ft
Ground Clearance 1.17 ft
Center Line of Rear Axle to Edge of Counterweight 6.33 ft
Center Line of Rear Axle to Hitch 5.50 ft
Wheelbase 11.00 ft
Overall Length (without bucket) 24.58 ft
Hinge Pin Height at Carry Height 2.58 ft
Hinge Pin Height at Maximum Lift 14.83 ft
Lift Arm Clearance at Maximum Lift 11.92 ft
Rack Back at Maximum Lift 59 degrees
Rack Back at Carry Height 49 degrees
Rack Back at Ground 40 degrees
Maximum Width over Tires (loaded) 9.25 ft
Tread Width 7.00 ft
Note All dimensions are approximate and based on Michelin 23.5R25 XHA2 L3 radial tires.


BENEFITS & FEATURES
Key Features


Benefits to help get your work done efficiently and effectively

RELIABILITY, PRODUCTIVITY AND FUEL EFFICIENCY


  • 10% more fuel efficient than K Series*
  • Up to 25% more efficient than H Series*
*Fuel efficiency is measured in mass of material moved per volume of fuel burned. Average efficiency improvement as tested and analyzed for an average composite cycle and stand configuration with variations per comparable model with and without economy mode active. Factors influence result variation such as, but not limited to, machine configuration, operator technique, machine application, climate, etc.

Linkage and Work Tools


  • Performance Series buckets and range of work tools
  • Optimized Z-bar with best-in-class visibility
  • –0°/+5° parallelism
  • Increased tilt capacity at height, equal to payload
  • Fusion™ « zero-offset » coupler (option)

Engine and Aftertreatment Advancements


  • Cat® C7.1 engine
  • Meets Tier 4 Final/Stage IV emission standards
  • Cat Clean Emissions Module with Selective Catalytic Reduction
  • Productive Economy Mode

Transmission Advancements


  • 5-speed powershift transmission with single clutch speed shifts and torque based down shifts
  • Lock up clutch torque converter with lock-to-lock shifting
  • Split flow oil system and multi-viscosity oil

Axle Advancements


  • On-the-go disc-type front differential locks (front and rear fully automatic option)
  • Caliper disc parking brake
  • Bevel gear shrouds

Next Generation Hydraulic Systems


  • Next generation main valve
  • Next generation ride control system with dual accumulators
  • Next generation implement pump with increased displacement
  • Full flow and kidney loop filtration
  • Load-sensing hydraulics with simultaneous hydraulic functions
  • 3rd and 4th function (option)

EASE OF OPERATION – Best-in-class Operator Environment


  • Optimized all-around visibility
  • Steering wheel (E-H joystick steering option)
  • Touch screen multifunction color display with integrated controls and rearview camera
  • Stair-like ingress and egress
  • New wider door and increased glass area
  • Seat-mounted fingertip electro-hydraulic implement controls
  • Large convex rearview mirrors with integrated spot mirror
  • Remote door opening (option)
  • Automatic climate control
  • Viscous cab mounts
  • Low operator sound levels

EASE OF OPERATION – Advanced Technology with Cat Connect


  • Link technologies, like Product Link™ to monitor equipment and manage production using online VisionLink® software
  • Payload technologies, like Cat Production Measurement (option) to measure payloads and optimize productivity
  • Detect technologies, like the rear vision camera to keep people safe and help the operator work more productively

SERVICE ACCESS


  • One-piece tilting hood with side and rear doors
  • Centralized service centers for hydraulic and electrical components
  • Windshield cleaning platform and harness tie-off


CONNECT. DISCUSS. SOLVE.
CATERPILLAR EQUIPMENT MAINTENANCE ONLINE COMMUNITY

LATEST POSTS FROM THE ONLINE COMMUNITY ...

Cat C7 Serpentine Belt Diagram
Have a freightliner with a Caterpillar C7 engine. Cannot find the belt diagram on the truck&nbs...  [More]

242D Engine Mounts
I need to replaced the engine mount bushings on my 242D but the bolts hit the fuel tank.I there a se...  [More]

Engine Shutdown Due To High Crankcase Pressure
How can i verify that theres actually a high pressure in crankcase? Before shutdown, MPD also diplay...  [More]

963 Ac Vaccum On Low Side
Long story short blew the low side hose going into the compressor two weeks ago replaced hose and en...  [More]
HOW CAN WE HELP?
SHARE YOUR FEEDBACK OR ASK A QUESTION
Feel free to ask a question or share a comment about the information on this page.

To help us answer your question or respond to your comment, please enter your email address.