SH650 D

The new SH650 D provides the same tri-sectional design, lift and carry capacity, and maneuverability of the battery powered SH650 with the added power of a diesel power pack.


SPECIFICATIONS
Specifications
Carry Capacity 50.0 tons
Vehicle Length 38.32 ft
Vehicle Width 9.94 ft
Frame Oscillation 40.0 Degrees
Gradients Possible (gradient data short-term only) 25°
Ground Clearance 19.0 in
Maximum Speed with Load 12.0 mph
Motor/Engine Diesel
Power Rated at 240.0 hp
Pull Winch Rated at 38.0 tons
Steering Control stick
Steering Articulation 50.0 Degrees
Torque/Tractive Effort 88749.0 lb
Turn Radius (outside) 23.85 ft
Wheel Base 16.93 ft


Lift and Carry Capacity
Capacities Based on 54 × 26 Solid Tire at 1575 mm (at 62 in)
Without Ballast 50.0 tons


Operator’s Compartment
Components System Pressure Gauge
Components Warning Horn
Components RH Transmission Range Selection
Components LH Transmission Range Selection
Components Valve bank hydraulic functions: steering, bucket, bucket eject and winch/power take off
Components Park Brake Set/Release
Components Accumulator Pressure Gauge
Components Park Brake Override
Components Side Egress Access
Components One LinkOne CD which includes all above manuals in electronic format
Components RH Lighting Selection
Components Right Foot Accelerator Pedal
Components Engine Temperature
Components Converter Temperature
Components Low Oil Engine Shutdown
Components Intake Restriction Gauge
Components Engine Oil Pressure
Components Park Brake Release Pressure Gauge


Cab Option
Components Addition of 7th main control valve section and additional operator's control valve included.
Fixed height 508 mm (20 in) Cab Assembly MSHA certified cab, formed support plate, access handles, completely enclosed grid and dual corner opening doors
Hydraulically Adjustable 508 mm (20 in) Cab Assembly MSHA certified cab, formed support plate, access handles, completely enclosed grid and dual corner opening doors
Manual Adjustable 508 mm (20 in) Cab Assembly MSHA certified cab, formed support plate, access handles, completely enclosed grid and dual corner opening doors
Type Cab is manually adjustable.


Drive Train
Axles Front and rear rigid mounted outboard planetary axles with wet disc spring applied, hydraulically released brakes.
Cooling System Heavy Duty DST cooling system with 179 kW (240 hp) capability.
Cooling System Four and one-half fins per inch, 20.68 MPa (3,000 psi) pressure wash capable, brass tubed, cooling system.
Drive Lines 7 and 8.5 Series shaft with 76.2 mm (3 in) slip joints.
Power Component DST Catalyst
Power Component Water Cooled Exhaust Manifold and Turbocharger
Power Component Charge Air Cooler
Power Component Intake System with Intake Flapper Valve Shutdown
Power Component DST Safety System
Power Component DST Flameproof Alternator
Power Component DST Air start package including: air starter, starter oil injector, water separator, pilot valve and operator control valves.
Power Pack One, 179 kW (240 hp), Cummins with DST Scrubber, MSHA Par 7E-A Approved
Power Pack - Note Initial machine equipped with C8.3 138 kW (185 hp), but cooling & emissions control components sized for 179 kW (240 hp) engine
Transmission Six speed, power shift Clark 32000 transmission with 7C input and dual 8.5C outputs. Isolator mounted with dipstick fill.
Transmission External shell type, water to oil, shell cooler.


Fire Suppression
Type Also one 22.7 kg (20 lb) Class 10A60B: Hand held unit located in the operator's pit.
Type Automatic/Manual with linear detection wire.


Lift Attachments
Fork Assembly Designed to lift and carry 45 tonnes at 1575 mm (50 tons at 62 in) from the load lift plate mounted to the machine
Fork Assembly Set of 2134 mm (84 in) overall length up-set forged forks
Quick Attach Lift Plate Designed to lift and carry 45 tonnes at 1575 mm (50 tons at 62 in) from the face of the load lift frame
Quick Attach Lift Plate The plate mounts directly to forks through two parallel pockets and is held in place with two drop pins chained to lift plate
Quick Attach Lift Plate 2134 mm (84 in) (Fork Assembly Required)


Lighting System
Type Four MSHA approved head lights
Type DST MSHA approved lighting package


Dimensions (Approximate)
Cab Height with 508 mm (20 in) Cab (lower cab heights available on request) - With 48-in Tires 68.0 in
Cab Height with 508 mm (20 in) Cab (lower cab heights available on request) - With 54-in Tires 70.0 in
Chassis Height (nominal) - With 48-in Tires 48.0 in
Chassis Height (nominal) - With 54-in Tires 50.0 in
Empty Weights 100000.0 lb
Frame Oscillation ±20°
Ground Clearance: Nominal (please reference sales drawing for ground clearance profile) - With 48-in Tires 16.0 in
Ground Clearance: Nominal (please reference sales drawing for ground clearance profile) - With 54-in Tires 19.0 in
Inside Turn Radius 13.58 ft
Length Less Load Lifting and Battery Lift Forks 31.5 ft
Length with 2133 mm (84 in) Lifting Fork 38.5 ft
Length with Lift Plate Attachment 40.0 ft
Outside Turn Radius 23.66 ft
Overall Width - With Attachments and 48-in Tires 9.83 ft
Overall Width - With Attachments and 54-in Tires 9.91 ft
Steering Articulation 100° Total
Tram Speed (calculated based on 4% rolling resistance): With Cummins C8.3 Engine 138 kW (185 hp) - Level and Empty on 0% Grade 8.5 mph
Tram Speed (calculated based on 4% rolling resistance): With Cummins C8.3 Engine 138 kW (185 hp) - Level and Loaded on 0% Grade 4.15 mph
Tram Speed (calculated based on 4% rolling resistance): With Cummins C8.3 Engine 179 kW (240 hp) - Level and Empty on 0% Grade 10.1 mph
Tram Speed (calculated based on 4% rolling resistance): With Cummins C8.3 Engine 179 kW (240 hp) - Level and Loaded on 0% Grade 5.03 mph
Wheelbase 16.91 ft


Hydraulic Installation (Standard)
Components JIC fittings with high pressure hosing; MSHA 2G flame resistant approved.


Brakes
Hand Pump Floor mounted hand pump located to the right of operator.
Hand Pump Activating this pump enables the operator to release the brake without power on the unit for towing a disabled vehicle.
Service Left foot-pedal actuated wet disc brakes at all four wheels.
Service Automatic Emergency/Park Brake Release.
Service A dash mounted monitoring gauge keeps the operator constantly informed of the accumulator’s status.
Service Accumulator is not permitted to fall below a certain residual pressure to assure this continued availability.
Service Demodulating/Failsafe parking and service brakes with cooling circuit.
Service Hydraulic power is supplied through a one gallon accumulator and is monitored by a charging/unloading valve.


Hydraulics
Bell-Crank Lift Cylinder Two (2) 203 mm (8 in) bore, double acting cylinders with load locking valves mounted on both the up and down functions.
Hydraulic PTO Two (2) quick coupler connections, 17.58 MPa (2,550 psi) maximum recommended operating pressure.
Pump Filtration One 5 micron filter on the accumulator circuit
Pump Filtration One 5 micron filter on the main hydraulic circuit
Pump Filtration One remote mounted 5 micron return filter
Pump Filtration One 5 micron filter on the pilot valve circuit
Pump Filtration Standard - Three pressure filters
Pump Motor Converter mounted, variable displacement, pressure compensated pump, 120.37 L/min (31.8 gal/min).
Reservoir Use Mobil Type 424 Hydraulic Oil
Reservoir Clean out plate to permit access to suction in-line strainer and cleaning and draining without removing from the machine
Reservoir An oil level sight gauge is located on the side of the tank and is easily visible.
Reservoir A 189 L (50 gal) capacity reservoir
Reservoir End mounted magnetic drain plug
Reservoir Spin-on filter/breather
Reservoir Fill System System allows refilling of reservoir through the return line oil filter that is located in the top of the oil reservoir
Reservoir Fill System Venturi Jet refill system located on opposite side from operator on the middle frame
Steering Cylinder Two (2) 152 mm (6 in) bore, double acting cylinders with dual relief setting at 15.86 MPa (2,300 psi).
Tilt Lift Cylinder Two (2) 241 mm (9 1/2 in) bore, double acting cylinders with load locking valves mounted on both the up and down functions.


Dual Lift System
Center Section Entire center section area manufactured with T1 steel.
Center Section Center section is designed with hardened 102 mm (4 in) diameter pivot pins & spherical bearings to provide maximum load transfer
Oscillation Section An 813 mm (32 in) diameter bearing with 44 mm (1 3/4 in) diameter rolling elements provides 20 degrees of oscillation.
Standard Load Lift Face Plate A combination bell-crank arm and bell-crank lifting cylinder for vertical lifting and tilting cylinders
Standard Load Lift Face Plate Heavy duty forged alloy steel forks, 152 mm × 356 mm × 2134 mm (6 in × 14 in × 84 in)
Tri-Section Frame All high stressed areas are manufactured with T1 steel.
Tri-Section Frame Design produces a maximum of stability while maneuvering with a heavy load
Tri-Section Frame Design features multiple plate, modular construction for maximum strength and structural integrity
Winch A fully hydraulic operated, 31 751 kg (70,000 lb) winch, with two speed pay in/out.
Winch Cable Assembly Equipped with a swaged-on thimble, connecting link and swivel hook
Winch Cable Assembly The standard winch cable is 25.4 mm (1 in) diameter, 6 × 37, IWRC, EIPS, class bright cable


BENEFITS & FEATURES
Diesel for Endurance
Cat diesel roof support carriers incorporate the most efficient engines and powertrains available while boasting the lowest level of general body air emissions amongst underground diesel vehicles. Many proprietary developments - such as dry scrubber and wet bath exhaust systems with diesel particulate filtration and horizontal or vertical configuration cooling radiators - make Cat diesel roof support carriers a safe and powerful solution for your longwall move. They can move any roof support over any distance and over various roadway conditions with speed and efficiency.


Diesel for Endurance

Proven Yet Improved
Cat diesel vehicles across the product range share industry-proven drive units; diesel engines and other major components from the world’s leading OEM manufacturers. We combine this with our own expertise in developing low-emission solutions:
  • Particulate filtration system
  • Inline purifier catalytic converter
  • Zero-smoke dry particulate exhaust system
  • New wet scrubber exhaust system
  • Posistop brakes for extra safety
  • Positorque axles for superior traction
  • 4-speed power shift transmission for smooth operation

The Power You Need
A combination of Cat battery- and diesel-powered vehicles can offer the ideal solution for longwall installations and moves.


The Power You Need

Diesel-powered roof support carriers carry your roof supports the full distance at maximum speed and lowest cost. Diesel equipment is a good option for new longwall installations as they do not require electrical infrastructure such as cabling and charging stations and can operate at higher speeds over long distances, up steeper gradients and over rougher terrain - conditions not suitable for battery-powered vehicles.

Diesel Power for the Long Haul
Diesel-powered equipment is used in nearly all underground mines in various tasks and functions around the world.


Diesel Power for the Long Haul

There are many technical features of Cat diesel vehicles that make them unique in the underground mining industry. Their general body air emissions are one of the lowest in the field, and the fact that they are compact, powerful machines with a small roadway presence and the capability to be used for multiple tasks means a high return on investment.

Flexibility
Cat diesel-powered roof support carriers offer independence and flexibility when you need it most - during longwall moves and reinstallation.


The four-wheel drive and rear engine arrangement are designed to offer high stability and high tractive effort whether loaded or unloaded on the roadway or installing roof supports at the longwall face.

RAS - Rapid Attachment System
The Rapid Attachment System available for the CL10 and CL15 makes an accessory change a one-man operation, allowing a broad range of accessories to be fitted in moments without removing the backing plate. Utilizing the LHD with RAS attachments during longwall relocations can greatly reduce lost production time.


RAS - Rapid Attachment System

Each attachment is tested and performance rated.
  • Ejector plate bucket
  • Side shift forks
  • AFC chain reeler
  • Belt reeler
  • Cable reeler
  • Jib crane [static and slewing]
  • Work baskets
  • Fuel and lubrication module
  • Materials pod system
  • Concrete hopper


CONNECT. DISCUSS. SOLVE.
CATERPILLAR EQUIPMENT MAINTENANCE ONLINE COMMUNITY

LATEST POSTS FROM THE ONLINE COMMUNITY ...

Cat C7 Serpentine Belt Diagram
Have a freightliner with a Caterpillar C7 engine. Cannot find the belt diagram on the truck&nbs...  [More]

242D Engine Mounts
I need to replaced the engine mount bushings on my 242D but the bolts hit the fuel tank.I there a se...  [More]

Engine Shutdown Due To High Crankcase Pressure
How can i verify that theres actually a high pressure in crankcase? Before shutdown, MPD also diplay...  [More]

963 Ac Vaccum On Low Side
Long story short blew the low side hose going into the compressor two weeks ago replaced hose and en...  [More]
HOW CAN WE HELP?
SHARE YOUR FEEDBACK OR ASK A QUESTION
Feel free to ask a question or share a comment about the information on this page.

To help us answer your question or respond to your comment, please enter your email address.