Engine Output - SAE J1995 858 kW (1,150 hp)
Standard Bucket Capacity Face Shovel (heaped 2:1) - 10.0 m3 (13.1 yd3); Backhoe (heaped 1:1) - 10.0 m3 (13.1 yd3)
Operating Weight Face Shovel - 183 tonnes (202 tons); Backhoe - 186 tonnes (205 tons)
Engine output SAE J1995 - 2 × Cat C18 ACERT 1150.0 hp
Electric Motor - 6018 AC/6018 AC FS
Frequency 50 Hz (60 Hz on request)
Output 650 kW
Rated current IN 72A (at 6.3 kV)
Revolutions 1,500 min-1 (1,800 min-1 on request)
Starting current 350% of IN (197% of IN optional)
Type Squirrel cage induction motor
Voltage 6.3 kV ± 10% (other on request)
Electrical System (diesel drive)
Batteries (12V each) in series/parallel installation 4 × 210 Ah; 420 Ah - 24V
System voltage 24V
Working spotlights 8 × Xenon lights
Backhoe - Ground Pressure 18.6 N/cm2 (27.3 psi)
Backhoe - Operating weight 410060.0 lb
Backhoe - Standard track pads 2.62 ft
Shovel - Ground Pressure 18.5 N/cm2 (26.9 psi)
Shovel - Operating weight 404320.0 lb
Shovel - Standard track pads 2.62 ft
Bucket Payload 20.0 tons
Operating Weight - Backhoe 205.0 tons
Operating Weight - Front Shovel 202.0 tons
Engine Model 2 × Cat® C18 ACERT™
Gross Power - SAE J1995 1150.0 hp
Net Power - SAE J1349 1104.0 hp
Note Electric drive option available (650 kW) on 6018 AC/6018 AC FS
All buckets (FS and BH) are equipped with a wear package consisting of: - Special liner material covering main wear areas inside and outside of bucket - Lip shrouds between teeth
Shovel attachment with unique TriPower kinematics ensuring the following main features: - Automatic roll-back limiter to prevent material spillage - Kinematic assistance to hydraulic forces
Shovel attachment with unique TriPower kinematics ensuring the following main features: - Horizontal automatic constant-angle bucket guidance - Vertical automatic constant-angle bucket guidance
Shovel attachment with unique TriPower kinematics ensuring the following main features: - Constant boom momentum throughout the whole lift arc - Crowd force assistance
Type Inspection hole in boom (FS)
Type Special wear packages for highly abrasive materials on request
Type Pressure-free lowering of boom (FS and BH) and stick (FS) by means of a float valve
Type Welding procedures allow for internal counter-welding (double prep weld) wherever possible
Type Booms and sticks are stress-relieved after welding
Type Booms and sticks are torsion-resistant, welded box design of high tensile steel with massive steel castings at pivot areas
Retractable Service Station
Installation Retractable service station installed underneath the engine module and easily accessible from ground.
Alternators 2 × 150A
Aspiration Turbocharged and charge air cooled
Bore 5.7 in
Displacement 1105.0 in3
Emissions U.S. E.P.A. Flex, EU Flex
Fuel tank capacity 845.0 gal
Make and model 2 × Cat C18 (Tier 3)
Maximum altitude without deration at 20° C (68° F) - above sea level 6560.0 ft
Number of cylinders (each engine) 6
Stroke 7.2 in
Total rated gross power - SAE J1995 858 kW 1,800 min-1 (1,150 hp 1,800 min-1)
Total rated net power - ISO 3046/1 824 kW 1,800 min-1 (1,104 hp 1,800 min-1)
Total rated net power - SAE J1349 824 kW 1,800 min-1 (1,104 hp 1,800 min-1)
Automatic Lubrication System
Capacity of Grease Barrel 53.0 gal
Bottom Rollers (each side) 8
Components Chain links connected by hardened pins and bushings
Components Track guides
Components Acoustic travel alarm
Components Forged double-grouser track pads
Components All running surfaces of sprockets, idlers, rollers and track links are hardened
Components Fully hydraulic self-adjusting track tensioning system with membrane accumulator
Components Automatic hydraulic retarder valve to prevent overspeed on downhill travel
Gradeability of travel drives - maximum 88.0 %
Maximum tractive force 278440.0 lb
Parking Brakes Wet multiple disc brake, spring applied/hydraulically released
Support Rollers (each side) 2 plus a skid plate in between
Track Pads (each side) 47
Travel Drives (each side) 1 planetary transmission with 1 axial piston motor
Travel speeds: AC version - maximum 1.06 mph
Travel speeds: Diesel version - maximum 1.43 mph
All buckets (FS and BH) are equipped with a wear package consisting of: - Wing shrouds on side walls - Bottom edge protection
Components Switch in seat cushion to automatically neutralize the hydraulic controls when operator leaves the seat
Components Pneumatically cushioned and multi-adjustable comfort seat with lumbar support, seat heating, safety belt, head- and armrests
Components Roller blind at windshield
Components Windshield with parallel intermittent wiper/washer
Components All-round safety glass, armored windshield and sliding side window
Components FOPS (rock guard; approved acc. to DIN ISO 3449) integrated into cab structure
Components Joystick controls integrated in independently adjustable seat consoles
Components Fold-away auxiliary seat with safety belt
Components Emergency exit harness kit
Components Machine access via retractable boarding ladder, hydraulically operated
Components Robust instrument panel includes large colored BCS screen with transflective technology
Internal dimensions of cab - Height 7.05 ft
Internal dimensions of cab - Length 5.91 ft
Internal dimensions of cab - Width 4.27 ft
New Board Control System (BCS) Features: Electronic monitoring & data logging system for vital signs & service data of engines, hydraulic system & lubrication system
Operator’s eye level: AC version - approximately 20.34 ft
Operator’s eye level: Diesel version - approximately 17.72 ft
Hydraulic Oil Cooling
Diameter of fans 2 × 1120 mm (2 × 3 ft 8 in)
Oil flow of cooling pumps - AC version 608 + 218 L/min (161 + 58 gal/min)
Oil flow of cooling pumps - Diesel version 2 × 412 L/min (2 × 109 gal/min)
Hydraulic System with Pump Managing System
Hydraulic tank capacity - approximately 528.0 gal
Main pumps - AC version 2 × variable axial piston pumps
Main pumps - Diesel version 4 × variable swash plate pumps
Main pumps - Maximum oil flow - AC version 2 × 578 L/min (2 × 153 gal/min)
Main pumps - Maximum oil flow - Diesel version 4 × 412 L/min (4 × 109 gal/min)
Maximum pressure, attachment 4350.0 psi
Maximum pressure, swing pumps 5365.0 psi
Swing pumps - AC version 1 × reversible swash plate pump
Swing pumps - Diesel version 2 × reversible swash plate pumps
Swing pumps - Maximum oil flow - AC version 516 L/min (136 gal/min)
Swing pumps - Maximum oil flow - Diesel version 2 × 288 L/min (2 × 76 gal/min)
Total volume of hydraulic oil - approximately 660.0 gal
Bucket Capacity - Backhoe (heaped 1:1) 13.1 yd3
Bucket Capacity - Front Shovel (heaped 2:1) 13.1 yd3
Maximum swing speed - AC version 4.1 RPM
Maximum swing speed - Diesel version 4.7 RPM
Parking Brakes Wet multiple disc brake, spring-loaded/hydraulically released
Swing Drives 2 compact planetary transmissions with axial piston motors
Swing Ring Triple race roller bearing with sealed internal gearing
Balanced Combination of Power and Efficiency
Meeting Your Site Specific Needs with a Choice of Robust Drive System Options
Giving you the option to choose the drive system best suited for your operation, the Cat 6018/6018 FS can be equipped with either two Cat C18 diesel engines for greater mobility, or an electric drive for better efficiency.Reliable Cat C18 ACERT Engine
Delivering durable, reliable power that will keep your primary loading tool producing, the C18 has proven its ability to stand-up to the harshest mining conditions, providing the mobility and flexibility you need. In addition, they’re backed by our world-class dealer network, ready to provide service and support when needed.Efficient Electric Drive System on 6018 AC/6018 AC FS
Providing a lower cost-per-ton alternative to diesel powered hydraulic shovels, our electric drive option maintains the ruggedness you need and offers superior availability since no refueling and less service is required. This solution is ideal for operations that do not require a great deal of mobility and value a low cost-per-ton model.
Stay Up and Running More Consistently
Keep Producing and Ensure the Safety of Your Operators, Even During Single Engine Loss
You will realize enhanced safety, greater uptime, more productivity, and better serviceability as a result of our twin-engine concept.Enhanced Safety
The ability to move your shovel to a safe area for repair, away from high walls, blast zones, or other safety hazards, is still possible with the use of a single engine.Greater Uptime and More Productivity
Up to 65% of full production can still be achieved with the use of a single engine. This is due to the shovel’s continued ability to exert maximum digging forces, to lower the front attachment without requiring engine power (i.e., pressure-free), and to recuperate energy via its closed-loop swing circuit.Better Serviceability
Troubleshooting is greatly simplified and expedited with the ability to compare one engine versus the other.
TriPower System (Front Shovel Machines)
Superior Digging Capability and Bucket Fill Factors
Dig More Effectively with Our Unique TriPower Front Shovel Design
You will experience enhanced, easier and faster front shovel operation with TriPower, a system proven on over a thousand Cat hydraulic shovels worldwide. Generating superior mechanical leverage and control, our FS configured hydraulic shovels utilize a unique boom design that employs rotatable triangular rockers. This design facilitates quicker cycle times, increased effective lifting force, constant boom momentum, automatic constant bucket angle, and automatic roll-back limiter.Quicker Cycle Times
- Faster lifting speeds are achieved, because the design enables the use of smaller-diameter boom cylinders.Increased Effective Lifting Force
- Design transfers digging forces into the superstructure, creating supporting boom momentum in addition to momentum that is generated hydraulically.Constant Boom Momentum
- Allows smaller boom cylinders for higher lifting speed. - Keeps lifting speed constant. - Enables the shovel to lift a single load along the entire digging distance. - No retracting of stick cylinders is required, ensuring that all hydraulic pumps are supplying the boom-up function.Automatic Constant Bucket Angle
- Material spillage is avoided during boom lifting, because the filled bucket automatically maintains a constant bucket angle. - On conventional kinematics the operator has to control manually the bucket position during lifting which cut in half the available oil flow for the boom cylinders.Automatic Roll-back Limiter
- Preventing material spillage back on to the operator’s cab and machine superstructure, our system ensures that the bucket is always in a safe position, without operator control/manipulation, when it is at maximum height. - The boom cylinder continues to receive maximum oil flow, because the operator does not need to activate the bucket cylinder.
Easy Serviceability and Greater Productivity
Straightforward, Safe System Maintenance
Ensuring neat organization for safe operation, easy inspection, and fast service, and reducing the number of hoses needed, the main valve block is located on top of the boom.Faster Cycle Times
Faster cycle times are realized, because float valves are used to lower the boom instead of engaging pumps. This facilitates faster boom movements and allows other operating functions to occur simultaneously, such as bucket curl and stick in/out.
Independent Oil Cooling System
More Effective Oil Cooling for Extended Component Life
Protect and Extend the Life of Your Hydraulic Components and Seals
Providing a more efficient means of cooling, particularly in demanding applications, our unique independent oil cooling system will extend the life of your hydraulic shovel’s components.More Efficient Oil Cooling
Our system is independent of return oil, achieving efficiency through the utilization of dedicated pumps that provide cooling capacity as needed, whether the engine is idling or under load. That means optimum oil temperature is being maintained, even while your operator waits for the next truck to load. Competitive hydraulic shovels only provide cooling when the machine is working and the engine is under load. Additional efficiency is achieved via our electronically controlled radiator fan speed. The fans do not run until oil temperature exceeds a temperature of 50° C (122° F), saving energy.Optimal Oil Temperature Maintained
The high-efficient oil cooling system ensures that the oil temperature is only 25° to 30° C (45° to 54° F) higher than the ambient temperature. Thus the hydraulic oil working temperature ranges within the optimal operating viscosity range of 50° to 70° C (122° to 158° F).
Pump Managing System
Enhanced Efficiency, Component Life, and Control Response
Experience Improved Machine Control and Component Life with Our Intelligent Pump Managing System
Delivering optimal performance, our pump managing system continuously evaluates actual engine and hydraulic operating values against set values, and adjusts pump output accordingly. This results in efficient use of the engine for greater productivity. Pump managing system advantages include:
- Best possible utilization of engine output and engine overload avoidance via electronic load limit regulation
- Less energy consumption and less thermal load on hydraulic oil with zero oil flow regulation for main pumps
- Less fuel consumption and lower noise emission via automatic RPM reduction
- Reduced component wear and lower noise emission with automatic oil flow reduction for closing/opening of bucket clam
- Protection of components with automatic oil flow reduction if hydraulic and/or engine coolant temperature exceed set maximum
- Improved operator control response via on-demand pump flow
Closed-loop Swing Circuit
More Efficient Energy Use and Faster Boom Lift Motion During Swing
Load More Material, at Lower Cost, with the Energy Recovery Capability of Our Closed-loop Swing System
Delivering faster cycle times and improved energy efficiency, while also generating less heat, our closed-loop swing circuit provides distinct advantages over competitive machines utilizing open-circuit swing systems.Greater Efficiency via Energy Recovery
Kinetic energy captured during the swing motion is fed back into the system during deceleration, providing more power to drive the main and auxiliary pumps. Energy is saved during deceleration, because braking occurs via counteracting controls, as opposed to throttles used in open circuit swing systems.Energy Savings During Acceleration
Energy is saved during acceleration via torque control, providing a pressure balance valve that controls the swing pump against pressure in the closed-loop swing circuit, ensuring that only the minimum necessary oil flow is utilized at any given time.Faster Cycle Times
Faster boom lift motion during swing is achieved with our closed-loop swing system, increasing overall productivity.
Ensuring the Safety and Comfort of Your Operators
Get Peak Operator Performance with Our Safe and Comfortable Operator’s Cab
We understand that the most important factor in your hydraulic shovel’s effectiveness is the performance of its operator. To help make their workday as productive as possible, we’ve incorporated safety and comfort features into the 6018/6018 FS operator’s cab.Protection for Your Operator; Every Day, Every Shift
Supporting Peak Operator Performance with Comfort Features
- Safety glass is used for all cab windows, and armored glass for the windshield.
- Operator’s seat is equipped with integrated safety switch that automatically neutralizes the hydraulic controls when the operator leaves the seat.
- The height of the cab module ensures an eye level of approximately 5.4 m (17 ft 9 in), providing excellent visibility of the digging and loading areas.
- Cab meets Falling Object Protection System (FOPS) and DIN ISO 3449 standards.
- Pneumatically cushioned, multi-adjustable operator’s seat.
- Large, transflective color touch-screen display provides vital machine monitoring and diagnostic data for convenient troubleshooting and service assistance.
- Enhanced control response and servo adjustment capability via electro-hydraulic servo control.
Electronic Control System
Operate with Confidence
Enhanced Control Response and Optimized Hydraulic Engine Load Management
Help your team meet productivity and performance standards with our intuitive, informative on-board electronics.Electro-Hydraulic Servo Control - Enhanced Control Response
The system relays actuating signals from the joysticks, delivering fast and precise machine reactions facilitate a reduction in operator fatigue.Electro-Hydraulic Servo Control - Increased Uptime
Uptime is increased as a result of simplified troubleshooting and advanced diagnostic capabilities.Electro-Hydraulic Servo Control - Clean and Quiet Cab Environment
No hydraulic lines are present in the cab or the cab module, ensuring a clean arrangement with less noise emission.
Cat MineStar System and Technology Solutions
Evolving Your Mine for Greater Safety and Productivity
Helping You Enhance Safety and Productivity Through Technology
Aimed at enhancing the productivity and profitability of your hydraulic shovel, we currently offer a combination of Cat MineStar System offerings and Cat hydraulic shovel technology solutions.Cat MineStar System
Hydraulic Shovel Technology Solutions - Monitoring and Diagnostic System
Helping you achieve your goals for enhanced mine site safety, improved efficiency, reduced operating costs, and greater profitability, the Cat MineStar System provides the most comprehensive suite of mining technology products in the industry. It consists of a number of configurable capability sets - Fleet, Terrain, Detect, Health, and Command - that allow you to scale the system to your mine site needs. Cat MineStar System helps you manage everything from material tracking to sophisticated real-time fleet management, machine health systems, autonomous equipment, and more. The Cat 6018/6018 FS is currently able to utilize two of the Cat MineStar System capability sets:
- Fleet: Fleet provides real-time machine tracking, assignment and productivity management, providing a comprehensive overview of all your asset operations from anywhere in the world.
Terrain enables high-precision management of drilling, dragline, grading and loading operations through the use of guidance technology. It increases machine productivity and provides you real-time feedback for improved efficiency. The remaining Cat MineStar System capability sets are currently under development for the Cat hydraulic shovel product line.
Enhancing diagnostic capabilities and providing detailed troubleshooting functions, our Board Control System uses sensors throughout the machine to monitor operating data, record faults, and notify the operator audibly and visually. This promotes the earliest possible detection of faults and allows for timely maintenance planning and assistance for speedy repair.
Move More Material with Optimal Pass Match Pairings
Achieve Targeted Loading/Hauling Production with Perfectly Paired Cat Hydraulic Shovels and Off-Highway Trucks
For full truck payloads with minimum loading time, an efficient loading/hauling system begins with an optimized equipment match. Cat hydraulic shovels are matched with Cat off-highway trucks to maximize volume of material moved at the lowest operating cost per ton.
Front Attachment Options and Structures
Bolstering Your Investment with Robust and Durable Structures
Rugged Front Attachment Options Designed and Fabricated to Withstand Your Extreme Mining Conditions
To extend service life and ensure that your shovel keeps producing, our front attachment structures are designed for durability and dependability. Whether you equip your hydraulic shovel in backhoe or front shovel configuration, extended performance in the harsh mining conditions you face daily is accomplished through selection of high-strength steels and rugged castings, joined and thermally stress-relieved, to help you achieve your productivity targets.Front Attachment Structures Include:
- Heavy castings at all pivot points
- Better flow of forces and less welding seams, as top chords are made of one bend plate
- Entire boom and stick are stress relieved after welding
- Welding procedures allow for internal welding (double prep weld)
Longer Component Life for Better Swing System Reliability
More Reliable Swing Component Life
Extending component life and ultimately improving machine uptime, our swing system includes a triple-race swing roller bearing with internal gearing connected to an automatic lubrication system. For added reliability, all lube lines are located inside the roller bearing for maximum protection.Service Friendly
Easier maintenance is afforded by the free accessibility of swing gears and rotary distributor.
Tough and Long-lasting
Less Wear and Tear on Crawler Components
Extending track life and improving overall machine reliability, our undercarriages are engineered with extensive use of finite element analysis, steel structures are optimized, travel motors are well-protected, and a unique robust track chain incorporates a combined pad/link design. Further extending track life, a state-of-the-art track tensioning system with membrane accumulator automatically adapts the tensioning of the tracks, depending upon operating conditions.
Designed with Your Safety as Our Top Priority
Sharing your commitment to safety, and driven by our commitment to Zero Harm, we work tirelessly to design safe machines to protect your most important asset; your employees. Some examples of the safety-enhancing features of Cat hydraulic shovels include the following:Machine Access
Precise Bucket Control
- Hydraulically operated boarding ladder with emergency lowering via nitrogen accumulator ensures that ladder remains operational even when engines shut off.
- Machine swing and propel capability is switched-off when ladder is in down position.
• Minimizing the potential for material spill on to the attachment or cab, the TriPower automatic roll-back limiter prevents the bucket from being curled back too far.Operator Environment
- Switch in seat cushion to automatically neutralize the hydraulic controls when operator leaves the seat.
- FOPS and DIN ISO 3449 safety standards integrated into cab structure.
- Safety glass windows, armored windshield and sliding side window.
- An easily accessible, standard shut-off switch located in the cab shuts down the electrical system in case of emergencies.
- Additional shut-off switches are located on the machine, in the machine house or accessible from the ground with pull ropes.
Designed to Get You Back to Work Fast
Lowering your operating costs and maximizing your hydraulic shovel’s uptime and productivity is of supreme importance to us. To that end, we’ve made vital components more accessible and designed simpler systems to make maintenance activities quicker and easier.Open, Spacious Access to Components
Simple Hydraulic System
- Facilitating easier maintenance, exceptional accessibility is provided to systems like the swing motor, swing gearbox and rotary distributor in the well organized superstructure. The drive train is accessible from both the outside and inside of the superstructure.
- Easily accessed by walkways on both sides, the boom-mounted main valve block, a feature unique to Cat Hydraulic Shovels, provides a clean layout and reduces the number of hoses leading from the superstructure to the attachment.
• Ensuring neat organization for safe operation, easy inspection and fast service, the design of our hydraulic shovel reduces the total number of required hoses. Only four high-pressure hydraulic lines are connected between the superstructure and boom on the 6018/6018 FS.Easy Ground-level Fuel and Fluid Replenishment
• Quick fuel and fluid replenishment is made easy with a retractable service station underneath the engine module, accessible at ground-level.
Stay Up and Running with Service and Support from Our Unmatched Global Network
Commitment Makes the Difference
Cat dealers offer a wide range of solutions, services and products that help you lower costs, enhance productivity and manage your operation more efficiently. From the time you select a piece of Cat equipment until the day you trade or sell it, the support you get from your Cat dealer makes the difference.Dealer Capability
Cat dealers provide the level of support you need, on a global scale. Dealer expert technicians have the knowledge, experience, training and tooling necessary to handle your repair and maintenance needs, when and where you need them.Product Support
When Cat products reach the field, they are supported by a worldwide network of parts distribution facilities, dealer service centers and technical training facilities to keep your equipment up and running. Cat customers rely on prompt, dependable parts availability through our global dealer network, ready to meet your needs 24/7.Service Support
Every piece of Cat equipment is designed and built to provide maximum productivity and operating economy throughout its working life. Cat dealers offer a wide range of service plans that will maximize uptime and return on your investment, including:
- Preventive Maintenance Programs
- Diagnostic Programs, such as Scheduled Oil Sampling and Technical Analysis
- Rebuild and Reman Option
- Customer Support Agreements
Operating and maintenance costs are influenced by many application and site-specific factors, such as: material density and fragmentation, payload, bench height, truck positioning, ground conditions, amount of travelling and maintenance. Your Cat dealer can provide you with an understanding of the effects application characteristics and operating techniques have on maintenance and operating costs.Operation
Your Cat dealer can arrange training programs to help operator’s improve productivity, decrease downtime, reduce operating costs and enhance safety.
Higher Standards for a Better Tomorrow
Meeting the needs of today while conserving natural resources for tomorrow is the goal for all Cat machinery. The commitment to helping you operate safely and sustainably is affirmed in the production of the 6018/6018 FS hydraulic shovel.Cat Hydraulic Shovel Sustainability - Electric Power Option
Reduce your carbon footprint with our lower emission electric drive option.Cat Hydraulic Shovel Sustainability - Energy Recovery
Emit less heat and improve energy efficiency via the energy recovery capability of the closed-loop swing circuit.Cat Hydraulic Shovel Sustainability - Rebuilds
Decrease your energy use and material consumption with a machine that’s designed to be rebuilt.