Parts & Service // Expert Advice // Seven Steps To Clean Fuel
Print Version
SEVEN STEPS TO CLEAN FUEL

High pressure in fuel systems improves fuel atomization and helps reduce emissions, but it can also cause accelerated abrasive wear in the fuel system. Our experts explain three major factors that affect fuel system life and offer seven recommendations to help you ensure that your fuel supply is as clean as possible.
Seven Steps To Clean Fuel
 FACTORS AFFECTING FUEL SYSTEM LIFE

Generally, there are three major factors that affect fuel system life:

  • WATER. Water breaks down the protective film strength of fuel, leading to plunger scuffing and seizure failures. Low sulfur fuels have lower film strength and lower natural resistance to scuffing or seizure.
  • ABRASIVES. Small abrasive particles enter the fuel tank through unfiltered tank vents or come from the petroleum distillation process. These particles cause the injector cartridge to wear out, which results in internal leakage and reduced fuel delivery.
  • SUPPLY PRESSURE. A pressure of about 100 psi achieves complete filling and proper operation of injectors. Low supply pressure causes incomplete filling, which results in erratic fuel delivery and eventually cavitation damage to the injector.


KEEP YOUR FUEL SUPPLY CLEAN

These seven recommendations will help you ensure that your fuel supply is as clean as possible:

  • FUEL TANK DRAIN. Condensation from regular heating and cooling cycles creates water in fuel storage tanks. Debris enters vented fuel caps through normal tank breathing. Both water and debris are heavier than fuel and settle to the bottom. Fuel tank drains should be located at the lowest part of the fuel tank and drained daily.
  • TWO-MICRON TANK BREATHER FILTER. Up to two-thirds of the dust trapped in the two-micron secondary fuel filter comes through the vented fuel cap. A two-micron tank breather filter can significantly extend secondary fuel filter life.
  • WATER SEPARATOR. While modern fuel injectors are designed to tolerate small amounts of water in fuel, poor fuel storage practices and condensation can cause undissolved water to accumulate. A water separator reduces water content so fuel film strength is not weakened.
  • PRIMARY FUEL FILTER. A 10-micron primary filter removes large abrasive particles and prevents premature clogging of the secondary filter. A combination primary fuel water separator filter and secondary fuel filter helps keep water out of the system.
  • BYPASS FLOW. Circulating fuel not used by the injectors is called bypass flow. An insufficient amount of bypass flow results in high fuel temperatures. “Cooking” of the fuel yields tar-like particles that can cause the nozzle check to stick open, resulting in overfueling. Regular fuel filter replacement helps to prevent this problem.
  • FUEL SUPPLY PRESSURE. If fuel supply pressure gets too low, a vacuum bubble can form. This may cause injector damage when system pressure recovers and the bubble implodes, causing cavitation wear. A “headless plunger” design, used in most new injectors, eliminates cavitation problems.
  • SECONDARY FUEL FILTER. As pressures up to 30,000 psi occur in injectors, even small particles cause excessive abrasive wear. A high-quality two-micron fuel filter helps reduce wear.



CONNECT. DISCUSS. SOLVE.
CATERPILLAR EQUIPMENT MAINTENANCE ONLINE COMMUNITY
LATEST POSTS FROM THE ONLINE COMMUNITY ...

G3516 Low Compression And High Exhaust Temp.
I have one cylinder with low compression and also high exhaust temp. Other cylinders ok. No detonat ...  [More]

GEMINIS1963
PUEDE UN MOTOR CALENTAR POR TENER PROBLEMAS EN LA BOMBA HIDRAULICA ? HABLO DE UNA EXCAVADORA 330 IM ...  [More]

1996 3116
Installed new injectors and truck will not run .. Found that fuel is not getting to fuel pump .. An ...  [More]

3116 Running Problem
Just installed new injectors in my dump truck and truck will not run now..  it seems that it is sta ...  [More]
SHARE WITH US
WEBSITE FEEDBACK FORM
Did you find what you were looking for on this page?
Feel free to share your comments about the information on this page.


If you would like us to respond to your comments, please enter your email address.




 CALL NOW TO LEARN MORE

Danny Lay
865-595-1032
Send me a message

 EMAIL THIS PAGE TO A FRIEND
 
 
JOIN OUR EMAIL LIST
Sign up to receive Stowers news, expert advice and tips, and specials in your email inbox.
DIESEL PARTICULATE FILTERS FOR STATIONARY STANDBY ENGINES
Learn more about retrofitting existing diesel engines with diesel particulate filters. (PDF 113KB)
FUEL CONTAMINATION CONTROL
Dirty fuel is your engine’s worst enemy. Learn how to protect your engine. (PDF 1.5MB)
PROTECT YOUR FUEL SYSTEM
Learn how to protect your fuel system with Cat Fuel Water Separators and PrimeTime Priming Pumps. (PDF 242KB)
HIGH EFFICIENCY FUEL FILTERS
Take a closer look at the protection and performance offered by Cat High Efficiency Fuel Filters. (PDF 377KB)
EFFECTS OF ULTRA LOW SULFUR DIESEL FUEL ON GENSET ENGINES
Learn about the risks of using Ultra Low Sulfur Diesel Fuel in your generator set's engine. (PDF 147KB)
DOWNLOAD ADOBE® READER®
If you do not have Adobe® Reader® to view PDF files, get it free at the Adobe® website.
CONTACT A SALES REP
Find your Stowers sales rep by entering your ZIP code.
 

safety.cat.com


SAFETY MEETING TOPICS
Use our Toolbox Talks to lead safety meetings at your job site.
REFUELING EQUIPMENT
Think about safety even while refueling a machine.
SAFETY, HEALTH, AND ENVIRONMENTAL TOOLBOX TALKS